SDS Sequence mode: Stop after end frame is reached
October 6, 2022
Many SIGLENT SDS series oscilloscopes feature Sequence mode, which can be used to capture multiple trigger events that can be replayed like frames in a movie. In this video, we show how to use SINGLE trigger mode to stop acquisition after the user-defined sequences have been captured.
VNC Viewer for easy LAN control of multiple instruments
October 6, 2022
In this video, I connect an SDS6000A series oscilloscope and SDG7000A series arbitrary waveform generator to a computer using a LAN and highlight some of the features of a commercially available VNC(r) software tool. If you are remotely monitoring instrumentation, these types of tools can be very helpful in displaying information.
SDS6000A Introduction
October 12, 2021
Power Supply design: Testing! Not Guessing!
April 22, 2021
In this video, Thomas Rottach from SIGLENT EU presents information on overcoming common power supply design issues through different testing methods. The first presentation of this material was at the Power Electronics Forum @ virtual Electronica 2020.
Oscilloscope Search and Navigate example: Quickly identify dirty power/brown out on the power line
May 1, 2020
In this video, we use the Search and Navigate feature of the SIGLENT SDS2X Plus scope to isolate and indicate low voltage conditions of an input signal. Here, we use an SDG signal generator to produce a 60 Hz sine wave and we introduce a few periods of much lower voltage.. simulating dirty power/brownout conditions … Continued
Power Supply Design: Load Step Response with a SIGLENT DC Electronic Load
April 3, 2020
In this video, I compare the response from two power supplies using a stepped load to show the differences between a well-tuned supply and one that exhibits excessive ringing. Also, add in some basic instrument requirements to help get you started making your own step load tests. Here, I use a SIGLENT SDL1X-E DC Electronic … Continued
SDS1004/SDS2000X-E series Embedded Web Control
November 5, 2019
The SIGLENT SDS1004X-E series (4 channel only. Does not apply to the SDS1202X-E), SDS2000X-E, SDS2000X Plus, SDS5000X, and SDS6000A series of oscilloscopes feature a web control interface that provides remote instrument control without additional software. In this video, we show you how to configure the scope for wired LAN or wireless WiFi connection and an … Continued
SDS1X-E Bode II Testing by Chris Grossman
August 8, 2019
Chris Grossman (@batray) reviews the SIGLENT Bode II capabilities that were added with the four-channel XE firmware version 6.1.33: This function also applies to the following oscilloscope and generator series: SDS2000X-E SDS2000 X Plus SDS5000X SDS6000A SDG1000X SDG2000X SDG6000X SDG7000A
Frequency Response Curves (Bode Plot) using an Oscilloscope and Function Generator
September 17, 2018
In this video, we show how to use the automated Bode Plot feature of the SIGLENT SDS1004X-E series of four-channel oscilloscopes to create a frequency response curve. This function also applies to the following oscilloscope and generator series: SDS2000X-E SDS2000 X Plus SDS2000X HD SDS5000X SDS6000A SDG1000X SDG2000X SDG6000X SDG7000A SAG1021 SAG1021i There is … Continued
SDS1004/SDS2000X-E series Embedded Web Control
March 2, 2018
The SIGLENT SDS1004X-E series (4 channel only. Does not apply to the SDS1202X-E), SDS2000X-E, SDS2000X Plus, SDS5000X, and SDS6000A series of oscilloscopes feature a web control interface that provides remote instrument control without additional software. In this video, we show you how to configure the scope for wired LAN or wireless WiFi connection and an … Continued