More on Trigger Status Messages
August 8, 2019
There are 6 types of trigger status messages for the SIGLENT SDS series of oscilloscopes. The trigger status indication is located near the upper-right-hand side of the display, as indicated in this picture: Here are their definitions: Armed. The oscilloscope is acquiring pre-trigger data. All triggers are ignored in this state. Ready. All pre-trigger data … Continued
Currently supported instruments for use with the SIGLENT USB-GPIB adapter
August 8, 2019
The SIGLENT USB-GPIB adaptor currently works with the following SIGLENT instruments: Multimeters – SDM3065X/SDM3065X-SC SDM3055/SDM3055-SC SDM3045X Function/Arbitrary waveform generators – SDG6000X Series SDG5000 Series SDG2000X Series SDG1000X Series SDG1000 Series Spectrum & vector network analyzers – SSA3000X Series SVA1000X Series Oscilloscopes – SDS1000CFL
Four channel SDS1X-E Firmware 6.1.26 adds Serial Decoding Table CSV data save feature
August 8, 2019
The four-channel SDS1X-E series firmware 6.1.26 adds the ability to save serial decode data as a CSV formatted file. You can find the latest firmware here: SDS1X-E Firmware Configure SDS1X-E to deliver stable serial decoding on the signal of interest. In this example, we are looking at an I2C signal. NOTE: Single trigger will freeze … Continued
USB host connector power limits for instrumentation
June 14, 2019
SIGLENT instruments with USB ports can supply 500mA steady current at 5 V.
Oscilloscope Specifications: What does “div” mean in the specifications?
February 27, 2019
The term “div” for most SIGLENT specifications is equal to the Vertical Scale value (Commonly shown in units of Volts/div). Take the specification for the DC Gain Accuracy of a SIGLENT SDS1052DL+ For ranges ≤ 100 mV/div, the DC Gain Accuracy is given as ± [3% × (|reading|+|offset|) +1% × |offset| +0.2 * div+2 mV] If: Reading = 0.5 … Continued
X-E Instrument Control Websock error: [Object event]
February 14, 2019
If you attempt an Ethernet connection to your X-E series oscilloscope and receive the following error: Check the operating system revision of the oscilloscope. This is indicated as the second value of the Software Version that can be found on the System Info screen of the Utility menu. To find the Software Revision: Press … Continued
Where do I find environmental, EMC, and other compliance information for your products?
January 10, 2019
Information regarding product compliance is available on the datasheet for each product. Contact your local Siglent office for more details if you have trouble finding what you need. You can also write info@siglent.com
Are your instruments FCC compliant?
December 14, 2018
Test and measurement equipment is exempt from FCC emissions limits per CFR 47, Part 15, para 15.103(c): https://www.gpo.gov/fdsys/pkg/CFR-2002-title47-vol1/pdf/CFR-2002-title47-vol1-sec15-103.pdf Specifically: “(c) A digital device used exclusively as industrial, commercial, or medical test equipment.”
Measurement Data Depth SDS2000X vs. SDS1/2 X-E
December 14, 2018
One of the more powerful features of digital oscilloscopes is the automatic measurement function. Most modern scopes allow you to measure 20 or 30 separate waveform parameters including rise/fall time, phase difference, peak-to-peak voltage, and more. Some functions can actually measure large data sets to provide a “running average” of the measurement over a long … Continued
The number of data points for low, medium, and high resolution Bode Plot scans X-E series oscilloscopes
November 28, 2018
The SIGLENT X-E series of oscilloscopes feature Bode Plot capability for quickly collecting frequency response data on devices. There are three frequency sweep resolutions available: Low Resolution = 21 data points/sweep Medium Resolution = 101 data points/sweep High Resolution = 501 data points/sweep