Potential Solutions to Easy software window rendering/font issues
March 8, 2018
The installation of SIGLENT EasySpectrum and other “Easy” software is typically uneventful. But, there may be an occasional issue. Here are some steps that may help clear up any issues that you may encounter: Here is an example of a mis-rendered window view of EasySpectrum: Here are some steps that may help fix the issue: … Continued
What instruments accept SCPI commands for remote control?
October 25, 2017
All SIGLENT instruments (except for the SHS1000 and SHS800 hand-held oscilloscopes) support SCPI remote control commands. For more information, download the specific instrument programming guide located on the product page.
SSA3000X Tracking Generator Low Frequency Output Performance
October 25, 2017
The lowest output frequency for the tracking generator (SSA3000X-TG option) output on the SIGLENT SSA3000X series of spectrum analyzers is specified at 100 kHz with an output flatness of +/- 3 dBm. The TG functions below this frequency, but the flatness and accuracy can vary significantly. In this operating tip, we show some typical performance … Continued
Why does the noise floor of my analyzer raise when I enable the tracking generator?
October 25, 2017
There is an increase in the noise floor when enabling the tracking generator. This is due to the IF (intermediate frequency) feedthrough from the Tracking Generator (TG) circuit. You can check the specifications documents for your analyzer. In many cases, they show the DANL spec’s with the TG off due to the increased noise floor … Continued
Sweep modes, RBW, and Span settings for the SSA3000X
October 25, 2017
The SIGLENT SSA3000X series of spectrum analyzers has three distinct sweep modes available, they are auto, sweep and FFT. By default, auto is selected. It selects the best mode based on RBW, Span, and Tracking Generator settings. Sweep mode configures the spectrum analyzer to work as a traditional swept superheterodyne design. Breaking the sweep span … Continued
How to enable Log frequency scaling with the SSA3000X
October 25, 2017
The Siglent SSA3000X spectrum analyzer can be configured to display amplitude and frequency with logarithmic (log) scaling. Vertical (amplitude) scaling on a spectrum analyzer is typically shown in log scaling with dBm as units as a default. The Horizontal (frequency) scaling is typically linear, but some applications prefer log frequency scaling. To manually enable log … Continued
How do I invert colors on saved image files with an SSA3000X?
October 25, 2017
The Siglent SSA3000X spectrum analyzer can save images of the display in a number of common picture formats, including JPG and BMP file types. Normally, the background of the images matches that of the instrument. This black background may be problematic when physically printing these images for reports. To save on printer supplies, you can … Continued
SSA3000X File Types
October 25, 2017
The SSA3000X can save files in a number of formats that can be useful for saving/recalling configurations, correction and limits, as well as raw trace data. Those include: – State files (*.STA file extension): These files can be used to save and recall the instrument configuration. They are saved in binary format, which is designed … Continued
How to save a file with the SSA3000X
October 25, 2017
The SSA3000X can save a number of file types to either internal memory or an external USB memory device. Here are instructions on how to view and save files: – If you intended to save to an external device, insert a USB memory device into the front panel USB slot. – Press File located on … Continued
SSA3000X External Reference Clock Recommendations
October 25, 2017
The external clock input of the SSA3000X series of spectrum analyzers has the following specifications: External Clock Input: 1-5 Vp, 10 MHz, edge-detected, sine (preferred). Square waves containing a 10 MHz rising edge can work, but harmonics may affect performance. Clock Output: Approximately 1 Vp (0-1 V), 10 MHz sine wave.